ISG2000 6.3.0r16b.0 firmware update to 6.3.0r26
Hi all, I have a Juniper ISG2000 (No IDP) with the version 6.3.0r16b.0, I would like to upgrade the firewall firmware to : 6.3.0r26. What are the changes in the new version? What are the open points?...
View Articleunable to access DVR through ssg5
We are trying to port a dvr through the system to access the cameras and cannot see them here is a copy og the config, hope you can show me where is issue is. the cameras are on port 3777 tcp 3778...
View ArticleSSG5 keeps dropping connection to Shaw modem
Little history have a lihts and water system connected to the juniper which is remotely controlled from another location. The issue is that the connection between the shaw modem and the juniper loses...
View ArticleHow to remove entry from BGP advertisment
Hello, We have BGP VPN to teo remote systems with IPs 172.188.32.45 and 172.188.33.45 . We are using same VR for both VPNs. How we could stop local network 192.168.6.0/24 to be advirtised via BGP to...
View ArticleScreenOS - How can I read the "get session" output correctly?
Hi guys, Following a flow captured from an old NetScreen in my company (for security reasons, I changed the IP addresses):id 1916387/s1*,vsys 1,flag 00200440/4000/0003/0000,policy 2549,time 1, dip 0...
View ArticleVPN tunnels usage - SSG140
Hi,I´d like to know how to check the VPN usage for the SSG140.The get license shows 500 VPN Tunnels:SSG140A(M)-> get license-key Model: Advanced Sessions: 48064 sessions Capacity: unlimited number...
View ArticleLast Firmware update for NS5GT
What is the last firmware upgrade for the NS5GT? Where might I be able to obtain it? Whenever I try changing"Enable web management Idle Timeout" under "Configuration > Admin > Management" and...
View ArticleClik here to view.
Two Dual ISP by one ISG1000
Greeting All, I need your support for the below subject. I have dual ISP, the first ISP (Speed 70 Mbps) already connected with ISG1000 and working correctly, my organization needs to install &...
View ArticleDo I need to create route if both subnet using the same virtual router
After created the 2 subnetsethernet0/1 192.168.1.0/24 Layer3ethernet0/2 192.168.2.0/24 Layer3There were 4 route entries auto created192.168.1.0/24 ethernet0/1 Protocol C192.168.1.1/32 ethernet0/1...
View ArticleJuniper firewall as l2tp client
Is there a model of Juniper able to work like a l2tp client? So, for example having two firewall Juniper and one of them working like a l2tp-server and the other one working like l2tp-client and...
View ArticleInternal cannot reach internet
Ethernet0/0 with IP 1.1.1.1. Which connected to the modemI've an existing subnet 192.168.1.0/24 set at interface ethernet0/1. Computers within this subnet can reach internet .Now, I created another...
View ArticleClik here to view.
ssg20 routing problem
Hello everyone, I am new to Juniper, I hope someone can help me solve this problem. Below is the network diagram of my environment. I have established a policy based VPN connection from Site1 to...
View ArticleConfiguring VIP for VNC on SSG20
Hi to everybody here...I'm trying to get familiar with Juniper firewall... so I'm a newbieConfiguring a port forwarding for VNC service I could notice that in Network > Interfaces > Edit >...
View ArticleVPN tunnel using LTE modem
So i have a need for connecting a remote site (trailer) using cellular to our main SSG140 @ our datacenter. We purchased a Netgear LTE modem and put it in bridge mode and put a SSG5 behind it. Plugging...
View ArticleNetscreen SSG-550M and Windows NLB Issue
Hello Everyone, I'm troubleshooting an issue with windows NLB cluster and facing some challenges to make it work. When we add a new VM to the cluster, NLB VIP doesn't respond to hosts outside its vlan...
View ArticleSSG140 maxed out at about 75MB when traffic shaping is turned on
All,I'm seeing an issue where simply turning on traffic shaping without any policy or bandwith configuration on the interface results in a max throughput of about 75MB. I have a 300mb internet...
View ArticleOSPF help with 'recv bad LSR from neighbor'
I'm trying to get OSPF over an IPSec tunnel between an SSG-20 and a Ubiquiti EdgeRouter. The tunnel is fine and works well with static routing, but OSPF is not working. They are exchanging OSPF data,...
View Articlepurpose of bgroup
What is the use of bgroup for the interfaces? they work like link agg? I can't find a good guideline that explain this. any help?
View ArticleTranslating IP
Hello all, Please help me figure out how to create rule for my purpose. I would like to retranslate public IP to private IP when trying to connect to external IP from internal network. Let's say i...
View Article